The SnapPower Guidelight product

I try to start projects and then get distracted by the next item on my list and often leave things somewhat completed.Being a homeowner, I often have a “honey-do” list that endlessly extends. It’s bad, I know. This ADOS (Attention Deficit…Ooooh Shiny) is a fault. So, I love it when I find a project that is easy, one that I can say that I hit the 100% completion mark on. Recently, I wanted to add a nightlight into our master bathroom. Sure, that is easy, right? But I didn’t want to just plug one in. In my tech-filled home, plugs are scarce, a luxury almost. So when the folks at SnapPower contacted me to see if I wanted to test out their SnapPower Guidelight product, it got my interest.

HTD SnapPower - prongs

I have done plenty of electrical projects in my home. Anything from running new electrical for an overhead fan to putting up dimmable lights in my garage to replacing most of my light switches with dimmers. Electrical work is actually pretty easy, provided you turn off the main power to whatever circuit you are working on to following code as close as you can. Of course, I have done fairly basic projects. Putting in the SnapPower Guidelight was probably the EASIEST electrical project I have done. And there was no wiring/re-wiring involved.

 

An important thing to note about the SnapPower solutions, there are some plugs that are NOT supported, GFCI plugs are one of these. Be sure to check their list of un-supported plugs before trying this. Luckily, the plug I wanted to install the SnapPower Guidelight was NOT a GFCI plug but one that was tied into one. This meant that I could throw the test circuit breaker on the GFCI plug and it effectively cut the power to the plug where I was going to install the SnapPower Guidelight.

Be sure, if you use this GFCI method, that the power IS actually off on the plug you are working with. You can do this by plugging something into the plug you are going to upgrade and try turning it on. If there is no power, you can proceed.

The next step is to simply unscrew the screw that holds the old faceplate in place. Then you take the SnapPower Guidelight and put it in place and screw it back in. Then turn the power back on to that plug either at the circuit breaker or at the GFCI level.

What the SnapPower Guidelight does

The design of the SnapPower cover plate is where the magic is. There are two prongs that connect to the power (which you can see in the picture below). These prongs complete a circuit and power the 3 LED lights of the Guidelight.

HTD SnapPower - back

There is a tiny photocell sensor that detects the amount of light in the room or hallway. When it gets darker, the lights go on. These LED lights will supposedly last over 25 years before they start “wearing out.” The lights put out about 3 lumens which is equivalent to most plug-in nightlights.

And the energy expense to run the SnapPower Guidelight is pretty much negligible. For a year’s worth of use, it costs about 10 cents (depending on the price of your power).

HTD SnapPower - Guidelight photosensor & LED lights

The other nice thing, which was important for me, was that it doesn’t take up any of the valuable plugs in my home. I still have access to the two electrical sockets of the wall.

USB Charging SnapPower Faceplate

There is another product that SnapPower has that is designed the same way the Guidelight is and with the same easy install method. The SnapPower Chargers also just replaces a cover plate and has the same two prongs that complete the circuit.

HTD SnapPower - Charger & USB port

At the bottom of this faceplate is a USB charger on the side. It also doesn’t use up any of the plugs (and trust me, in my family, having charging solutions is quite important).

The USB charging plug is only 1 amp, so it is better for smaller smartphones. It can charge tablets but will take a bit longer than using a 2.1 amp charger. The charger does have built-in surge protection for the charging. There are no LED lights as part of this product though.

HTD SnapPower - Guidelight lit

The SnapPower Charger retails for $20 per cover plate. And the SnapPower Guidelight retails for $15. Given how easy it is to install these…it’s a SNAP…(sorry), it’s hard not to upgrade at least one plug in your home. These are great for hallways or bathrooms. Basically, you install it and just forget it. Definitely a nice upgrade!

Disclosure Text : I have a material connection because I received a gift or sample of a product for consideration in preparing to write this content. I was/am not expected to return this item or gift after my review period. All opinions within this article are my own. Also, some of the links in the post above are “affiliate links.” This means if you click on the link and purchase the item, I will receive a small affiliate commission. More information can be found in my About page.

Related posts:

  1. Run Internet Connections through Electrical Power with NETGEAR PowerLine (PL1000)
  2. Using the Sun to Power your Gadgets & Light the Way – WAKAWAKA POWER
  3. Charging Up on the Go with the Sharper Image Restore Charging Valet
  4. Charge Your Gadgets Even When the Power is Out with the Scosche solBAT II Solar Charger
  5. The Dexim BluePack S3 & S8 – A Portable Battery Pack Designed for James Bond

Post Author: Tech Review